E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   - Forward suspension bracket
      Electronic control by rigidity of shock-absorbers (EDC)
      Removal and installation of an amortization rack
      Dismantling amortization rack/shock-absorber. Removal and installation of a screw spring
      Check and shock-absorber utilization
      Removal and installation of the bearing of a wheel
      Removal and installation of a beam of a forward suspension bracket
      Removal and installation of the lever of a cross-section suspension bracket
   + Back suspension bracket
   + Steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics


Heavy Metal & Reflected


Removal and installation of an amortization rack

 REMOVAL

1. Remove a support of a brake and adhere it a wire to a body, address to the Section Removal and installation of a brake disk/support of a forward brake.

Do not disconnect a brake hose. Otherwise after assembly it is necessary to remove air from system

2. Take out from the holder cables of ABS and the sensor and wear of brake shoes. Rasstykuyte shtekerny connections in a plug box.

3. Disconnect from the stabilizer a bar, having unscrewed a nut. The stabilizer from a provorachivaniye hold a wrench.

4. Remove the hinge of steering draft at a rotary support, address to the Section Removal and installation of a cable of the parking brake.

5. Check, whether marking of provision of the amortization rack, put at manufacturer is visible. Otherwise put with paint a strip being continuation of a gap of the basic bearing.

6. Bring under an amortization rack from below a garage jack that the rack after its office did not fall.

7. Unscrew a nut of fastening of an amortization rack, take out a bolt.

8. Dissolve shlitsa of a rotary support and fix its situation. Repair trucks for this purpose apply the special BMW tool - 31 - 2-200.ki.

9. Uncover an amortization rack.

10. Rasstykuyte shtekerny connection of electronic control of amortization if it is available, and uncover a cable.
11. Unscrew three nuts of fastening (shooters) of a support of an amortization rack.

12. Press a rotary support the lever, for example the extension piece of a face head, down so that to overturn a rack outside from a wheel casing.

For this purpose the assistant is required. Watch to damaging a wheel casing. A wing cover (2). If necessary remove the bottom guard of an impellent compartment, address to the Section Removal and installation of the bottom guard of an impellent compartment.

13. Squeeze out a big screw-driver or mount the shock-absorber from a rotary support.

Do not separate an amortization rack from a rotary support rotary motions. It can lead to emergence radial рисок, bringing to rack damage.


 INSTALLATION

1. Insert an amortization rack into a rotary support so that marking coincided with the provision of a shliyets on a support.
2. Carefully insert an amortization rack into a wheel casing and fix it the moment of 20 Nanometers at the top support.
3. Join shtekerny connection of electronic control of amortization if it is available, and close it a cover.
4. Establish a cover on a support of an amortization rack.
5. Press a rotary support a garage jack up against the stop. Pay attention to marking on a rack.
6. Insert tightening a bolt and tighten it a new being self-stopped nut the moment of 80 Nanometers.
7. Establish steering draft at a rotary support, address to the Section Removal and installation of a cable of the parking brake.
8. Establish wheels directly.
9. Fix a bar of the stabilizer a new being self-stopped nut the moment of 60 Nanometers.
10. Join shtekerny connection of ABS and the sensor of wear of brake shoes. Fix connection in the holder.
11. Establish a brake support, address to the Section Removal and installation of a brake disk/support of a forward brake.