E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   + Forward suspension bracket
   + Back suspension bracket
   - Steering
      Security measures at work with a safety cushion
      Removal and installation of a steering wheel
      Removal and installation of the top facing of a steering column
      Removal and installation of a tip of steering draft
      Removal and installation of steering draft
      Hydropump fastening
      Removal of air and filling of hydrosystem of the amplifier of a wheel with liquid
      Check and adjustment of corners of installation of wheels
+ Body
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics


Heavy Metal & Reflected


Removal and installation of a steering wheel

Surely familiarize with the Security measure Section at work with a safety cushion.


 REMOVAL

1. Disconnect a weight cable from the storage battery. The battery is in a luggage carrier behind the right lateral facing.

At a detachment of the battery the memories given in electronic blocks, for example, memories of malfunctions of the engine are erased.

2. Isolate a weight cable at the storage battery to exclude casual contact.

3. Turn out three bolts of fastening of the bottom facing of a steering column.

4. Press inside the top facing of a steering column from both parties in the area shown on an illustration and pull the bottom facing down.

5. Rasstykuyte shtekerny connection of a safety cushion (orange color).

6. Rasstykuyte shtekerny connection of the switch of a steering wheel if it is available.
7. Turn out from a reverse side of a steering wheel two Torx screws of 27 mm.

8. Raise knot of a safety cushion and расстыкуйте the following shtekerny connections:
   a) Cartridge for ignition (1).
   b) Sound signal (2)
   c) Podrulevogo of the switch (3).

9. Remove the block of a safety cushion and put an amortization plate up, for example in a luggage carrier.

10. Establish wheels directly. Markings on a steering wheel and a spindle should coincide.

11. Turn out a bolt (the shooter on an accompanying illustration).

After a reversing of a bolt the safety spring (F) which holds a contact ring on the average situation becomes more active. After a bolt reversing by no means it is impossible to turn a steering wheel. Otherwise the contact ring is damaged.

12. Mark the provision of a steering wheel concerning a spindle.
13. Remove a steering wheel from a spindle. If necessary it is possible to use a stripper.

Do not force down and do not get in blows a steering wheel. Watch that at removal of a wheel not to damage a cable.


 INSTALLATION

1. Check the provision of a contact ring on a steering wheel. Markings (1) should coincide. Address to an accompanying illustration. If the contact ring was displaced or not confidence that it is on the average situation, adjust the provision of a contact ring as follows.

2. Press a spring (F) and turn a contact ring to the left and to the right against the stop. Count total number of turns and halve them.

3. Turn a ring from an emphasis on the number of the turns equal to a half received so that markings (1) coincided. Release a spring (F).

4. Check, whether there is a lever of switching of signals of turn on the average situation. Otherwise at installation of a steering wheel the cam can be damaged.

5. Establish a steering wheel on shlitsevy connection of a spindle so that earlier put markings coincided. Watch that the lock pin (1) entered into a groove (2).

6. Tighten a bolt of fastening of a steering wheel the moment offered by Specifications.

It is impossible to turn a steering wheel to an inhaling of a bolt of fastening. It is possible to damage a contact ring.

7. Establish the block of a safety cushion and join shtekerny connection, address to the Section "Removal".
8. Insert a safety cushion into a steering wheel and tighten a bolt of fastening the moment of 2 Nanometers. Thus watch to jamming a cable.
9. Join shtekerny connections of a safety cushion (orange) and the switch of a steering wheel.

10. Establish the bottom facing of a steering column. Press it and fix. Thus the stopper (1) should enter into a hook (2). Address to an accompanying illustration.

On an illustration facing is shown from below.

11. Fix facing by three bolts.
12. Connect a weight cable to the storage battery. Establish hours.
13. Pass on the car and check correctness of provision of a steering wheel at movement directly. The top spoke of a wheel should be located horizontally.
14. If the provision of a steering wheel another, again remove it and displace.
15. Check functioning of a sound signal.
16. Check automatic return of the switch of signals of turn.


The dirty steering wheel can be cleared a neutral cleaner and warm water. Do not apply for this purpose a nazhdachny skin.