E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Removal and installation of a forward wing

Observe security measures at performance of body works, see the corresponding subsection.


 REMOVAL

1. Wring out a wide plastic shpatel a persistent level on a wing.
2. Remove forward lateral repeaters of signals of turn, address to the Section Replacement of filament lamps.
3. Remove a headlight peak. For this purpose disconnect a peak inside, wring out down from both holders and unhook.
4. Remove upward protection of an otbortovka.
5. Mark the provision of a forward wheel in relation to a nave. It will allow to establish an otbalansirovanny wheel in former situation. Weaken bolts of fastening of a wheel on the car standing on wheels. Lift and establish the car on supports.

6. Unscrew bolts of fastening and remove sideways a peak of a forward wheel casing (1).

7. Unscrew bolts of fastening of an internal wing. Take out clips, previously having beaten out pins an opravka inside. If pins have a cap, at first take out pins a screw-driver, and then remove a clip. Remove an internal wing.

8. To Otboltita a wing from a rack And.

9. Disconnect an internal wing from a car rack.

10. Open a door and through a gap unscrew a fastening bolt to a car rack.

11. Turn out the top back bolt (the shooter on an accompanying illustration).

12. Turn out the top bolts of fastening (an arrow on an accompanying illustration) covered.

13. Mark with a felt-tip pen the provision of a loop of a cowl.
14. Fix a cowl so that after an otvorachivaniye of bolts of fastening on a wing not to damage adjacent details of a body and a windscreen.

15. Weaken a bolt (1), a bolt (2) turn out.

Watch to losing a washer under a fastening bolt.

16. The wing strongly sits owing to existence of a protective anticorrosive covering of the bottom of a body. Therefore the hair dryer creating temperature not less + 400°С is necessary for its removal.
17. Soften the hair dryer with a flat nozzle the top and bottom areas of the bottom of a body. Then remove from below in forward area of a prileganiye of a wing a sheeting. It is especially important to make it in this area, otherwise the wing at removal can be deformed.
18. Remove a wing.


 INSTALLATION

1. Clear adjacent surfaces of a wing. If necessary отрихтуйте wing.
2. Impose on adjacent surfaces a usual sealing tape for a wing.
3. If necessary restore a paint and varnish covering.
4. Put a wing, approximately expose it and wrap fastening bolts, without tightening them.
5. Establish a cowl and fix it bolts, address to the Section Removal and cowl installation.
6. Expose a wing. Watch dense landing of consolidation around a headlight. Watch a uniform gap on the relations to a door and a cowl, address to the Section Body gaps.
7. Tighten all bolts of fastening of a wing.
8. Put on wing inside a sheeting.
9. Fix holders of a bumper.
10. Fix internally a wing and a peak of a casing of a forward wheel. Insert clips and enter pins.
11. Fix bolts a forward wheel. Do not oil bolts or plastic greasing. Establish a wheel so that the markings put at removal coincided. Lower the car on wheels. Tighten bolts of fastening of wheels cross-wise the moment of 100 Nanometers.
12. Insert the top sealant of a wing.
13. Establish the top protection of edges.
14. Fix from above a headlight peak.
15. Establish lateral repeaters of turns, address to the Section Replacement of filament lamps.
16. Establish on a wing a slip.