E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Adjustment of provision of a cowl

The hummock drive of both locks of a cowl should not have люфтов. The cover of a cable should be completely in directing the lock. Otherwise at impact on a cowl drive the cable in the directing can slip that will lead to impossibility of opening of locks.


If the adjusted cowl is displaced concerning the situation, not tinted places are visible.


 PERFORMANCE ORDER

1. Adjust position of the persistent screw (1) of the left and right loops so that the A=25 size of ± 1 mm.
2. Check an emphasis (2). If necessary replace a loop

Adjustment of a drive of a cowl

 PERFORMANCE ORDER

1. Adjust the provision of a cowl by the adjusting device. Address to an accompanying illustration.

The cable should not be tense. On an illustration the cable and locks are shown on a portable element.

2. If it is necessary, adjust a course of a drive of a cowl the adjusting screw (an arrow on an accompanying illustration).

3. Completely screw an emphasis.

Adjustment of lateral provision of a cowl

1. Address to an accompanying illustration.

 PERFORMANCE ORDER

1. Weaken bolts of fastening (1) and (2) left and right loops so that the cowl could be shifted.

2. Close a cowl and expose it rather right and left wings.

If the range of adjustment does not suffice, weaken bolts of fastening of loops of a cowl to a body and displace them concerning a body.

3. Carefully open a cowl and fix cowl bolts.

Adjustment of height of a back part of a cowl

 PERFORMANCE ORDER

1. Adjust cowl height around loops. For this purpose close a cowl and measure a deviation on cowl height in relation to wings.
2. Open a cowl and bring under it a support or ask to take the assistant.

3. Turn out bolts (1) and (2) and depending on a deviation from the correct situation take out or insert laying.

4. Tighten fastening bolts at the left and on the right.
5. Again check situation on height. If necessary repeat adjustment.

Adjustment of height of a forward part of a cowl

 PERFORMANCE ORDER

1. Weaken bolts of fastening of pins of the lock so that they could move.

2. Several times close the lock so that locks were combined.

Do not close a cowl on the lock.

3. Tighten bolts of fastening of pins of locks.

4. Unscrew a lock-nut (1) and turn a screw-driver a lock pin.

5. Thus adjust the equal provision of a cowl in relation to wings. Pay attention to achievement of a parallel gap in relation to facing.
6. Tighten a lock-nut.
7. Check, that locks were reliably fixed. If necessary repeat adjustment.

Emphasis adjustment

 PERFORMANCE ORDER

1. Open a cowl.
2. Turn out an emphasis so that the cowl was under some pressure. For this purpose make of plasticine two columns in height about 10 mm. Put them under an emphasis and close a cowl. Then open a cowl and measure height of an emphasis and the compressed columns. Turn out an emphasis on the received value of height of 0.5 mm. In the specified way adjust all emphasis.
3. Check, whether the cowl without gaps on all emphasis lies. If necessary repeat adjustment.

The cowl should not act under wings. Otherwise at movement of the car there is a wind noise

4. Measure a cowl vystupaniye over a rasseivatel of a headlight. It should make And = 4 ± 1 mm. Otherwise adjust the provision of a headlight.

5. Weaken bolts (arrows on an accompanying illustration) and displace a headlight forward or back.

Do not put pressure upon a headlight. If necessary displace the bottom bolts of fastening.

6. If the headlight was displaced, check its adjustment.