E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Removal and trunk lid installation

Trunk lid

1 — a trunk lid
2 — consolidation
3 — a loop
4 — the gas-filled shock-absorber
5 — a locking element
6 — the Torx screw with a washer
7 — the lock
8 — the plug
9 — the Torx screw with a washer
10 — a connecting bar
11 — the lock with a key
12 — the lock with a code
13 — a stopper
14 — a lock nut
15 — an emphasis with a pusher

16 — an emphasis
17 — a rubber stopper
18 — a lock washer
19 — a nut
20 — a washer
21 — саморез
22 — a cap
23 — an adjusting drive
24 — a connecting element
25 — the Torx screw for plastic
26 — consolidation
27 — an emphasis
28 — an emphasis
29 — the handle press
30 — the Torx screw with a washer
31 — the Torx screw with a washer


 REMOVAL

1. Disconnect facing.
2. Extend from a trunk lid a cable plait. For this purpose расстыкуйте shtekerny connection of a lamp of illumination of registration plate and uniform lock. Fix on tips a cord.

Cord leave in a trunk lid that it was simpler to put into place a plait.

3. Mark with a felt-tip pen the provision of a trunk lid at loops (the shooter on an accompanying illustration).
4. Bring a reliable support under a trunk lid or ask the assistant to take it.
5. Weaken screws (1) at the left and on the right. Screws (2) turn out.

6. Uncover a luggage carrier by means of the assistant.


 INSTALLATION

1. Put a trunk lid into place by means of the assistant. Screw screws (1), without tightening them.
2. Expose a cover according to markings and fix screws.
3. If the new cover is established, adjust its situation.
4. Involve in a cover a cord with electric wires of a lamp of illumination of registration plate and the uniform lock and join shtekerny connection.
5. Establish facing, replace the damaged clips.