E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Removal, installation and door adjustment

Installation and removal of lobbies and back doors are carried out equally.

 REMOVAL

1. Turn out a bolt (1) from each loop by means of a head of 10 mm. Address to an accompanying illustration.
2. Wring out sideways a screw-driver a stopper (2) from an axis (3).
3. Beat out on the top of opravky an axis (3) of a door brake.

4. Remove a door from loops and put it on a support. The height of a support should be such to exclude a tension of electric wires.

Do not damage a paint and varnish covering of a door and a forward wall. For protection of surfaces it is possible to stick them with a tape.

5. Disconnect the holder of the tip (an arrow on an accompanying illustration). Rasstykuyte shtekerny connection.

6. Lift a block. Thus, shtekerny connection undocks.


 INSTALLATION

1. Join shtekerny connection and fix it. Insert connection into a door rack. Fix the holder.

2. Put a door on the top and bottom loops. For this purpose the assistant is required. The door an axis (3) goes. By means of washers (5) it is possible to adjust the provision of a door on height. At installation of an old door adjustment, as a rule, is not required.
3. Screw in each loop a bolt (1).
1 — a bolt
2 — a body loop top
3 — a loop axis
4 — a door loop top
5 — a washer
6 — a lock washer

4. By means of a hammer insert an axis of a door brake and застопорьте it.
5. Close a door and check uniformity of a gap between a door and a body. If a gap non-uniform, weaken bolts of fastening of loops and adjust door height the top bolts.

At installation of a new door under a loop the remote washers, allowing to displace a door outside and inside are established.

The door should be leveled to (drive) only complete with hinged details, such as a window regulator, flew down etc. as the characteristic of shift of a door depends on weight. At adjustment remove door consolidations. If forward and back doors were removed, at first level a back door, then a lobby.

6. Weaken a bolt-1-locking fingers on a rack In by means of TORX key, and weaken a bolt-2-so that the locking wedge could be shifted. Do not change the provision of a locking wedge-3-on depth.

7. Raise and hold the door handle. Close a door, the height and an inclination of a locking wedge thereby is regulated.

To the direction of a locking wedge in a workshop it is applied щуп.

8. Carefully open a door and tighten bolts with effort of 30 Nanometers.

Shift of a forward edge of a door inside and a back edge outside no more than 1 mm is allowed. The worn-out locking element should be replaced.