E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Removal and installation of facing of a door

Here removal of facing of a forward door is described. Process of removal of facing of a back door is approximately similar. Differences are described at the end of the Section.

 REMOVAL

1. Disconnect a weight cable from the storage battery. The battery is in a luggage carrier behind the right lateral facing.

At a detachment of the battery the memories given in electronic blocks, for example, memories of malfunctions of the engine are erased. Address to recommendations of the Section Removal and installation of the storage battery.

2. Isolate a negative pole of the storage battery for an exception of casual electric contacts.

3. Turn out a bolt (1) in the air channel.

4. Take out a screw-driver a plafond of the bottom illumination of salon, расстыкуйте shtekerny connection and remove a lamp.
5. Take out a small screw-driver the switch (2) storing of provision of a seat. Rasstykuyte shtekerny connection also remove the switch.

6. Take out a small screw-driver the console of management (3) window regulators and exterior mirrors.

7. Remove the tip as follows:
   - Tip 1: Wring out sideways a small screw-driver a stopper, without taking out it. The switch is taken out upward by the lever mechanism.
   - Tip 2: Press down a lock hook and incline aside a lock clip. The switch is taken out upward.

8. Remove the management console.

 

9. Take out a peak (4) of an aperture of the door handle and turn out the bolt which was under it.

10. Disconnect door facing sideways and from below. For this purpose delay fingers of edge of facing. The arrangement of clips (arrow) is shown on an illustration.

11. Displace facing upward and release it from the central clip and from the top brackets. The clip is on facing inside in the area (And).
12. Shift a door drive through an opening in facing.
13. Raise and remove facing under the button of blocking of a door (2).

14. If the central clip (1) remained on a door, remove it, as is shown in an accompanying illustration and fix on facing.

15. Disconnect a loudspeaker cable. Unscrew screws of fastening and remove a box of a loudspeaker (1).

Observe security measures at work with a safety cushion, address to the Security measure Section at work with a safety cushion.

16. Rasstykuyte shtekerny connection (orange color) lateral safety cushion. Unscrew screws of fastening and put a safety cushion with a cover upward, for example in a luggage pocket.

17. Disconnect a cable (1) from the internal handle of a door and remove it.

18. If it is necessary, carefully remove penoplastovy facing from an internal part of a door.

That glutinous consolidation remained on polyfoam, it is recommended to remove it breakthroughs at low temperature.


 INSTALLATION

1. Carefully paste penoplastovy facing to a door.

Avoid facing damages as it can lead to draft emergence in salon. The glutinous weight should be put on all contour of facing.

2. Connect a cable to the internal handle of a door.
3. Fix on a door a lateral safety cushion. Join shtekerny connection.
4. Fix a box of a loudspeaker and connect the tip.

5. Check, whether there are all clips of internal facing of a door. The damaged clips replace.

6. Establish facing. The internal handle of a door and electric wires pass through openings. Lay sound insulation (1) round a cable of a window regulator and paste in a facing opening. Watch that the drive of a door was in a plastic support.

7. Insert facing from above over the fixing button. Put it at height of a level of mine of a door, delay from below a little and fix finger-tips at an angle down to a door in five top brackets.

Additions to removal and installation of facing of a back door

Remove the door handle (address to an accompanying illustration)
   a) Remove a screw-driver a peak.
   b) Turn out the screw which was under it.
   c) Remove from an axis the handle of lifting of glass and remove glass.