E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Removal and installation of the door lock

 REMOVAL

1. Close a window of a forward door. Other windows open.
2. Disconnect a weight cable from the storage battery. The battery is in a luggage carrier behind the right lateral facing.

At a detachment of the battery the memories given in electronic blocks, for example, memories of malfunctions of the engine are erased. Address to recommendations of the Section Removal and installation of the storage battery.

3. Isolate a negative pole of the storage battery to exclude casual contact.
4. Remove door facing.

Observe security measures concerning a safety cushion, address to the Security measure Section at work with a safety cushion.

5. Rasstykuyte shtekerny connection (orange) lateral safety cushion. Disconnect a pillow, having unscrewed screws of fastening and put it a cover upward, for example in a luggage carrier.
6. Remove the door handle.

7. Carefully remove plastic facing in a back part of cut of a door, incline it forward and fix in such situation by a sticky tape (1).

8. Disconnect at the door lock a nipple (1) and a cable (2).

9. Rasstykuyte shtekerny connection of the microswitch of the uniform lock also take out it down.


 INSTALLATION

1. Check, whether there is a clip pad (for the blade) below in the middle.

2. Insert the lock into a door. Thus a clip (1) (for the blade) the lock enter up into the blade (2) cylinders of the lock.

3. Join shtekerny connection of the electric motor of the uniform lock and fix it.
4. Connect the microswitch tip.
5. Insert a nipple and a drive cable into the lock.
6. Insert a handle cable into a door framework.
7. Accurately paste penoplastovy facing on door cut.

Avoid facing damages as it can lead to draft emergence in salon. The glutinous weight should be put on all contour of facing.

8. Establish the external handle of a door.
9. Fix on a door framework a lateral safety cushion. Join shtekerny connection (orange) a lateral safety cushion.
10. Establish internal facing of a door.
11. Attach a weight cable to the storage battery. Establish hours. Program radio receiver stations.
12. Check operation of the door lock, a drive of the lock and the uniform lock.