E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Removal, installation and adjustment of door glass

 REMOVAL

1. Remove upward an external level of window mine. Thus begin from below.
2. Remove door facing.

At the car with a lateral safety cushion disconnect a weight cable from the storage battery and remove a pillow, address to the Section “Removal and installation of the lock of a door”. Observe security measures at work with a safety cushion, address to the Security measure Section at work with a safety cushion.

3. Carefully remove penoplastovy facing in a back part of cut of a door, incline it forward so that the bottom adjusting screws were free and fix in this situation by a sticky tape.

4. Weaken bolts of fastening of a tightening block (an arrow on an accompanying illustration).

5. Incline glass a little forward and take out back upward.


 INSTALLATION

1. Insert glass into tightening blocks.
2. Attach the window regulator switch. If it is necessary, attach a weight cable to a battery battery room.
3. Close glass so that there was a gap of 10 mm.

4. Adjust the provision of glass, having reached the next sizes: And = 5.4 mm; In = 10 mm. Address to an accompanying illustration. For this purpose displace glass at open blocks in the longitudinal direction or displace a back block so that glass was parallel to a frame. In this situation tighten screws the moment of 10 Nanometers.

5. Rasstykuyte shtekerny connection of the switch of a window regulator. If it is necessary, disconnect a weight cable from the storage battery.
6. Establish door facing. If it is necessary, establish a lateral safety cushion, address to the Section Removal and installation of facing of a door.
7. Establish an external level of door mine so that it behind was aflush with a door edge.