E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of provision of a cowl
   Removal and trunk lid installation
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Slip replacement / firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of an electric window regulator
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a forward seat
   Device of a tension of a seat belt
   Security measures at the handling of the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of a jalousie of back glass
+ Onboard electric equipment
+ electric equipment Schemes
+ System of onboard diagnostics





Removal and installation of a forward seat

If the electric drive of adjustment of longitudinal provision of a seat has malfunction, see. The instruction at the end of the present Section.


 REMOVAL

1. Establish a seat vertically and shift it completely forward.

2. Turn out the screw of fastening of a seat belt.

3. Take away back a stopper (1) and take out it inside. A drive of adjustment of height of a belt (2) take out forward.

4. Turn out internal peaks upward (1). For this purpose unclench a clip. Take out it in the middle of (2) upward and remove back (3).

5. Rasstykuyte shtekerny connection (2), having opened a stopper (1).

6. Turn out back bolts.

7. Displace a seat completely back.

8. Electric drive of adjustment of a seat: Open a cover (And) forward. Open (1) stopper (In) and расстыкуйте shtekerny connection (2).

9. Turn out forward bolts.

If the seat is transported, acts in film or long time remains removed, block a natyazhitel of a seat belt, address to the Section Protection of the device of a tension of a belt.


 INSTALLATION

1. Establish a seat.

The rug should be in the region of points of fastening of screws, instead of between directing seats and a dnishchevy leaf. Otherwise at movement of the car there can be an extraneous noise.

2. Fix a seat new bolts. At first behind, then in front. Do not tighten fastening bolts.

If old bolts are applied, before installation grease them with means for fixing of carving connections of LOCTITE 270.

 

3. Fix bolts the moment of 40 Nanometers in sequence: the forward internal, forward external, back internal, back external.
4. Electric drive of adjustment of a seat: Put a seat completely back, join shtekerny connection and fix it. Establish a cover.
5. Connect multiitem shtekerny connection and fix it.
6. Fix peaks.
7. Connect a cable of a drive of adjustment on height and fix it.
8. Fix a seat belt below the moment of 50 Nanometers.

Only at malfunction of the electric drive of adjustment of longitudinal provision of a seat

 PERFORMANCE ORDER

1. Remove a peak internal directing seats.
2. Establish the mechanism of adjustment of an inclination of a seat in the top situation.
3. Disconnect the tip from the pump if it is available.
4. Unscrew two bolts of fastening of a lobby directing seats and overturn a seat back.
5. Turn out two bolts of fastening of the electric drive of adjustment of longitudinal provision of a seat and remove a drive.
6. Press the switch of adjustment of longitudinal situation.
7. Adjustment does not work: Attach a new drive and include it. If now adjustment works, the reducer is serviceable. It is necessary to replace only the electric drive.
8. The electric drive works, the seat does not move: The reducer is faulty. Replace it.
9. Rasstykuyte shtekerny connection of longitudinal adjustment of a seat.
10. Cut a connecting shaft.
11. Unscrew two nuts of fastening and remove a reducer at the left and on the right. After that the seat can be displaced a hand.
12. Fix bolts directing seats (only for removal).
13. Remove a seat and replace directing on the new.