E39 series BMW 5

since 1996-2001 of release

Repair and car operation



E39 BMW
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Diagnostics of malfunctions of onboard electric equipment - the general information
   Safety locks
   Fusible inserts
   Chain breakers (thermal relays)
   Relay
   Relay check
   Check of filament lamps
   Check of electric motors
   Check of electric switches
   Check of switches of lamps and electric motors
   Check of sensors
   Check of the electric motor of a screen wiper
   Stoplight check
   Check of a heater of back glass
   Removal and switch installation
   Removal and installation of the sensor of temperature
   Removal, installation and check of a sound signal
   Initialization of remote control by the uniform lock
   Adjustment of range of light of headlights
   Removal and installation of the electric motor of adjustment of range of light
   Replacement of safety locks
   Arrangement of safety locks
   Lighting devices
   Replacement of filament lamps
   Removal and headlight installation
   Adjustment of headlights
   Removal and installation of a back lamp
   Monitors
   Removal and installation of the block of the dashboard
   Replacement of lamps of the block of the dashboard
   Removal and installation of the switch of signals of a turn/screen wiper
   Removal and radio receiver installation
   Screen wiper
   Replacement of brushes of a screen wiper
   Removal, installation and adjustment snuffled a stekloomyvatel
   Removal and installation of a drive of a screen wiper/cover
   Removal and installation of the electric motor of a screen wiper
   Check and replacement of the pump of a stekloomyvatel
   Work with electric circuits
+ electric equipment Schemes
+ System of onboard diagnostics





Removal and installation of a drive of a screen wiper / cover

Screen wiper drive

1 — the screen wiper console
2 — the screw
3 — the electric motor
4 — a crank
5 — a bolt
6 — the bearing plug, oval
opening

7 — the bearing plug, round
opening
8 — the bearing plug, round
opening
9 — a damper ring, the top part
10 — a damper ring, the lower part
11 — a spring washer
12 — a nut


 REMOVAL

1. Mark position of levers of a screen wiper on a windscreen. For this purpose it is possible to use a sticky tape.

2. Remove covers from fastening nuts. For this purpose it is possible to use, for example, a small screw-driver.

3. Unscrew nuts.

4. Remove both levers of a drive of a brush from the forward passenger.

Do not deform the lever. It can break! The lever from the bearing remove a special stripper, for example, BMW-616000.

5. Remove up a cover of the left lever.
6. Unscrew a nut on the bearing of a brush and remove the lever upward.

7. Remove an adjusting washer of the lever from the bearing. The washer sits very strongly. Its removal needs a special stripper, for example BMW-616000, address also to an illustration 4.

8. Remove up rubber consolidation on a forward partition.

9. Disconnect collars (2) at air channels (1) at the left and on the right. Turn channels to the car center. For this purpose disconnect them from bayonetny clips.

10. Remove an insert of the filter of soaked-up air (3) at the left and on the right, address to the Section Replacement of the filter of air of salon.

11. Take out sideways a bracket (4). Disconnect behind the case of the filter (3) and remove it.

12. Uncover an airsupply. For this purpose open eight clips, having taken out a screw-driver pins.
13. Unscrew screws of fastening and uncover a drive of brushes.

14. Uncover a cable, having turned previously on 90 ° all clips.

15. Rasfiksiruyte also remove multiitem shtekerny connection. For this purpose displace down the clamp lever. Thanks to it the tip is disconnected from contacts.
16. Unscrew five bolts of fastening of a drive of a screen wiper and take out it.


 INSTALLATION

1. Insert a drive of a screen wiper and fix bolts by hand. Expose a drive so that it occupied the situation.

2. Fix a drive (And) bolts in sequence from 1 to 5 moment of 10 Nanometers.
3. Join shtekerny connection and fix it.
4. Establish a cover of cables and fix it four clips.
5. Fix screws a drive cover.
6. Establish an airsupply cover. Fix it clips.
7. Establish the case of the air filter and fix it in front a bracket.
8. Establish on the right and at the left filters of clean air, address to the Section Replacement of the filter of air of salon.
9. Insert the air channel into a bayonetny lock and fix it, having turned outside. At the end of turn insert the channel at first down at the filter, then press and fix a plastic collar. Move the channel in different directions, having checked reliability of its fastening. The second channel establish similarly.
10. Put rubber consolidation on a forward wall.
11. Establish an adjusting washer of the left lever of a cleaner and expose according to earlier put marking. Watch that the corner of installation of a brush to a windscreen made about 90 °. If the corner differs from specified displace the lever and an adjusting washer. Fix the lever and an adjusting washer the moment of 40 Nanometers.
12. Fix a cover of the left lever.
13. Establish into place both levers of a drive of the right cleaner.
14. Fix nuts the moment of 25 Nanometers and later 15 mines once again tighten the moment of 25 Nanometers.
15. Put on covers fastening nuts.